Halting Fax Spam - Spam
Fax Setting Parameters
This section describes fax setting parameters.
TX Settings (Transmission Settings)
Specifies the settings for sending a fax.
Immediate TX
Sets the machine to send a fax immediately when the original is scanned.
Default: [Off]
Select this when using Memory Transmission.
Select this when using Immediate Transmission.
Next Fax Only
Select this when using Immediate Transmission for the next transmission only.
Resolution
Specifies the resolution to use for scanning originals.
Default: [Standard]
Standard
Select this when the original is a printed or typewritten document with normal-sized characters.
Fine
Select this when the original is a document with small print.
Photo
Select this when the original contains images such as photographs or shaded drawings.
Density
Specifies the image density to use for scanning originals.
Default: [Normal]
Light
Normal
Dark
Pause Key Time
Specifies the length of pause time when a pause is inserted between the digits of a fax number.
Default: 3 seconds
1 to 15 seconds, in 1 second increments
Auto Redial
Sets the machine to redial the fax destination automatically when the line is busy or a transmission error occurs, if the machine is in Memory Transmission mode. The number of redial attempts is preset to two or three times, depending on the [Country Code] setting under [Admin Settings], in five-minute intervals.
Transmitter Header
Sets the machine to add a header to every fax you send. The header includes the current date and time, user fax name and number, job ID, and page information.
RX Settings (Reception Settings)
Specifies the settings for receiving a fax.
RX Mode
Specifies the reception mode.
Default: [Fax Only]
Fax Only
The machine automatically answers all incoming calls in fax reception mode.
Manual
The machine rings when it receives incoming calls. The machine receives faxes only when you manually receive faxes.
FAX/TAD
The machine receives faxes automatically when a fax call is received. Otherwise, the connected telephone answering device answers the call.
FAX/TEL
The machine receives faxes automatically when a fax call is received. Otherwise, the machine starts to ring.
Auto Reduction
Sets the machine to reduce the size of a received fax if it is too large to print on a single sheet of paper.
Note that the machine only reduces the size down to 74%. If further reduction is required to fit the fax on a single sheet, it will be printed on separate sheets without being reduced.
Default: [On]
(Default may be [Off] depending on the [Country Code] setting under [Admin Settings].)
Off
On
Ring Count Delay
Specifies the number of times the machine rings before it starts to receive faxes in Fax Only mode.
Default: 3 times
3 to pay as you go online fax 5 times, in increments of 1
F/T Ring Time
Specifies the length of time the machine tries to detect the fax calling tone in FAX/TEL mode.
Default: 15 seconds
5 to 99 seconds, 1 second increments
Tray Settings
Tray Use: Fax
Specifies the tray for printing received faxes. Note that only A4, Letter, or Legal size paper can be used for printing faxes. Make sure to select a tray that contains paper of the valid size.
If tray 2 is not installed, only [Tray1 Only] appears.
Default: [Auto]
Auto
The machine uses tray 1 and tray 2 if they contain paper of the same size. In this case, the machine starts to print from tray 1. If tray 1 runs out of paper, the machine automatically switches to tray 2 to continue printing. If tray 2 runs out of paper, load paper in tray 1.
Tray1 Only
Tray2 Only
Delete Document
Deletes unsent fax jobs remaining in the machine's memory.
This function is only performed when selected.
Memory Job Clear
To delete a fax job, select the desired job, and then select [Clear]. Selecting [Not Clear] exits to the previous level of the menu tree without deleting the fax job.
All Clear
To delete the fax jobs, select [Clear]. Selecting [Not Clear] exits to the previous level of the menu tree without deleting the fax job.
